Saturday, August 28, 2010

Extruder Checkerboard

The clay Extruder is one of my favorite tools.
So many things are possible with this tool.
Lots of people tell me all of the time "I can not cane".
You can, you just didn't have the right tool.
First step, stop telling yourself you can't.
Step two, find the right teacher.
Step three, find the right tool.
Step four, OPEN YOUR MIND!
Step five, have fun.

This is a way to fool everyone, even yourself.

All links below will lead to my husband's store, if you are looking for these products. Thank you so much for looking.
Thank you so much for supporting myself and my family.

Cernit polymer clay- black and white
Makin's professional clay extruder
Kemper Slicing Blades
1. Condition the white first , a half of package is enough. Get it nice and pliable.
2. Unscrew the handle until it is all the way out.
3. Roll a little log that is small enough in diameter to fit in the extruder barrel and fill it up. Place the square disk that comes with the extruder into the other end.
It is best to roll a log long enough to fill the barrel than to put in small logs to fill the barrel. The little logs will create air pockets.

4. Screw the handle back down slowly and at an even pace. Going slow helps the harder clays not shred on the edges of the square and other disk patterns. Extrude out all the white and then do the same thing with a half of package of black.






5. Press the two square coils together side by side. If using a smooshy clay do not smash together. Gently now.









6. Hold the ends of the square lengths and cut in the middle.









7. Lay one half right by the other half so it goes black, white, black, and then white.








8. Hold each of the ends again and fold gently in half so you can cut in equal halves again.








9. Flip one of the halves over so the pattern on one half is the opposite of the other.







10. Stack one half on the top of the other half.
Match up the lines of the squares as much as you can here.








11. Cut that stacked set in half.









12. Turn one half around 180 degrees horizontally and place on top of the other half. You can click on all the pictures to make them larger.









13. To make the checkerboard smaller press gently on each side of the 4 sides with your finger, one at a time.
Flip the cane from end to end and press on the 4 sides one at a time again.
Continue flip, press 4 sides, flip, press 4 sides, flip, press 4 sides... until it is smaller in size.





14. Ta-dah!!




15. You can also take one of the halves at this point and flip it end to end and place next to the other one.
This will multiply the pattern in one cane which makes it easier to apply to things in a row or border.










Slice off thin slices from the single checkerboard or the double with the clay slicing blade and add to your clay work. Or cut off slices and make beads out of them by piercing them with a needle or needle tool (bug sticker). Or cut off thin slices and bake and use in Encaustic painting, scrapbooking and collage.
OR??????

12 comments:

  1. Wow that looks easy enough for me to do. LOL
    Thanks for the tut and your husbands store link.
    Hope all is well with you.

    Nicole/Beadwright

    ReplyDelete
  2. Hi Marie, hope your back is better. This is great that you put tutorials on your blog. I have 3 extruders and love them.
    Love your millefiori idea about copying beading projects with clay.

    ReplyDelete
  3. I will have to try this Marie...thanks for sharing! I was looking for a short cut for the checker board cane and this is great!

    ReplyDelete
  4. Oh, I am sure you could do this Nicole.
    This is an incredible tool. I will be showing more things now and again too! There are also other techniques here, just search extruder.
    All is well. Thanks for caring Nicole!!

    ReplyDelete
  5. Thanks Bonnie, it is. It was out for so long, it is still a little twingy now and then though. I am babying it.
    This extrudar is a great tool!!
    That beading pattern millefiori is one of my favorites and helps new caners get the dynamics of caning pretty fast too!
    It is even possible to make focal beads that go perfectly with the loom beading too!

    ReplyDelete
  6. marie, this is like a foreign language to me and it is quite fascinating to see and hear you explain how this is done.

    and i laughed too. i could just hear you in the grocery line telling someone about your favorite tool the extruder. don't ask me why i think that's cute and funny hehehehee

    love
    kj

    ReplyDelete
  7. Lovely :) I tried extruding one of my canes once through the small circle disk - I actually got a really tiny version of my cane - bet I couldn't repeat that if I tried!!

    ReplyDelete
  8. Good Tute Marie! Thanks. I may just have to break out more of my stash of clay and have a play day. I am always amazed when I pull out my over 10 years old clay that it will still soften up and be usable, it was a good investment. Thanks for your generous sharing.

    ReplyDelete
  9. Thank for the neat tutorial, Marie! I know I can do this now! I've been playing with clay for awhile but have not attempted canes. When My daughter leaves next Sunday, I am going to try this for sure!

    ReplyDelete
  10. OH NO and I gave my extuder away!!!!! How was I to know??? You are too wonderful! Now what i get another and have you teach me : )

    Much Love Marie~Pattee

    ReplyDelete
  11. I so need me some new toys! I really love clay so much can be done with it. Hope that you had an enjoyable weekend Marie!

    (((HUGS)))

    ReplyDelete
  12. What a great little tutorial. You make it LOOK easy! :) Love the little checkerboard. Theresa :)

    ReplyDelete

I am so glad you stopped by. Please leave your words of wisdom. I look forward to them and I so enjoy reading them all.
Live to love, Love to create, and create to connect.
Marie

www.mariesegal.com
www.clayfactory.net